Skip to content
FlooringMath
Menu

Tile Installation Cost Calculator

What tile installation should cost for your area: tile, setting materials, labor, removal of the old floor and prep, shown as a low–typical–high range with every assumption visible. Type your own tile price and labor rate to replace ours.

Units
1. Area
  1. Subtract a tub, cabinets, door or window

      Net area: —

    2. The job
    3. Your prices (leave empty to use the ranges)

    Estimated cost

    Enter the area.

    What goes into the price

    total = tile × (area + waste) + setting materials × area + labor × area × pattern/material factor + removal × area + backer board × area + waterproofing × area

    The calculator prices each line separately so you can compare it with a quote line by line. When you type a tile price or a labor rate, that line uses your number for all three columns; the other lines keep their low–typical–high range.

    Assumptions used (US, late 2026)

    These are planning ranges, not a survey. They are in line with published cost guides (for example HomeGuide's tile installation cost guide lists tile labor at $8–$20 per sq ft and tile removal at $2–$7 per sq ft), but local prices differ widely between cities and seasons.

    Labor, set and groutLowTypicalHigh
    Floor$7.00$11.00$18.00
    Wall (dry area)$8.00$12.00$20.00
    Shower or tub walls$12.00$18.00$30.00
    Kitchen backsplash$12.00$20.00$35.00
    Tile, per sq ftLowTypicalHighLabor factor
    Ceramic$1.50$3.00$6.00× 1
    Porcelain$2.50$4.50$9.00× 1
    Large-format porcelain (24" and up)$4.00$7.00$14.00× 1.2
    Natural stone (marble, travertine, slate)$5.00$10.00$20.00× 1.2
    Glass or stone mosaic$10.00$18.00$35.00× 1.3
    Other items, per sq ftLowTypicalHigh
    Thinset, grout, spacers$0.75$1.25$2.00
    Remove: Carpet and pad$0.75$1.00$1.75
    Remove: Vinyl, laminate or wood$1.00$1.75$3.00
    Remove: Old tile$2.00$4.00$7.00
    Backer board / membrane, installed$2.00$3.50$5.00
    Waterproofing, installed$2.00$3.50$6.00

    Pattern labor factors: Straight × 1 · Brick / running bond × 1.05 · 1/3 offset × 1.05 · Diagonal × 1.15 · Herringbone, square to walls × 1.3 · Herringbone, 45° to walls × 1.35 · Chevron × 1.25 · Versailles / French pattern × 1.2.

    Worked example: a 10 × 10 ft bathroom floor

    Porcelain tile, straight layout, old tile removed, new backer board, our typical rates:

    • Tile: $495 (110.0 sq ft incl. 10% waste)
    • Thinset, grout, spacers: $125 (100.0 sq ft)
    • Labor (set and grout): $1,100 (× 1.00 for material and pattern)
    • Remove old surface: $400 (Old tile)
    • Backer board / membrane: $350 (installed)
    • Total: $2,470 (range $1,450–$4,190), about $24.70 per sq ft.

    What is not included

    • Subfloor repair or leveling (self-leveler is often $2–$5+ per sq ft when needed), moving a toilet or appliances, new baseboard or trim.
    • Plumbing for showers (valve, drain, pan), glass doors, electrical work for heated floors.
    • Permits, design fees and the contractor's markup on materials they supply.

    For exact quantities of tile, thinset and grout before you shop, use the tile calculator.

    Frequently asked questions

    How much does it cost to install 100 square feet of tile?

    With our default assumptions, a 100 sq ft porcelain floor with old tile removed and new backer board comes to about $1,450–$4,190 (typical $2,470, or $24.70 per sq ft). Without demolition and backer board it is roughly $1,720.

    How much do tile installers charge per square foot?

    Labor alone is usually quoted per square foot. Our starting bands are $7.00–$18.00 for floors, $12.00–$30.00 for shower walls and $12.00–$35.00 for backsplashes, which sit inside the $8–$20 range HomeGuide reports for tile labor. Small jobs often carry a minimum charge.

    How much does tile removal cost?

    Removing old tile and hauling it away typically adds $2.00–$7.00 per sq ft (HomeGuide lists $2–$7). Tile on a mortar bed or with a lot of thinset left on the slab is at the top of that range. Carpet is much cheaper to pull: about $0.75–$1.75 per sq ft.

    Why does shower tile cost more than floor tile?

    Walls are slower: every course must be supported while it sets, there are niches, corners, valves and edge trim, and the whole surface must be waterproofed. A 100 sq ft shower with porcelain, backer board and membrane runs about $2,023–$5,485 with our defaults.

    How much does a tile backsplash cost to install?

    A typical 30 sq ft kitchen backsplash in ceramic comes to about $450–$1,361 here, before any minimum charge. Per square foot it is the most expensive tile job because of the outlets, cutouts and short runs. Enter a minimum charge if your installer has one.

    Does the tile pattern change the labor cost?

    Yes. Every pattern beyond a straight grid adds cuts and layout time. We scale labor by 1.05 for offset layouts, 1.15 for diagonal and about 1.3 for herringbone, and the pattern also raises the tile waste. Natural stone and mosaics add another 20–30% of labor time.

    Is it cheaper to buy the tile myself?

    Often the tile itself is cheaper, but ask first: some installers charge more, or will not warranty the work, when they do not supply materials. Either way, buy all the boxes at once from one production lot and keep the receipt for unopened spares.

    Last reviewed November 22, 2026. How we check our math: About FlooringMath.