Skip to content
FlooringMath
Menu

Paver Sand Calculator

Both sands a paver project needs: the 1" bedding layer under the pavers (cubic yards, tons, bags) and the polymeric sand that locks the joints, calculated from the actual joint volume of your pavers.

Units
1. Paving area
  1. Net area: —

2. Bedding sand
3. Joint (polymeric) sand
4. Prices (optional)

You need

Enter the paving area.

Two sands, two calculations

Bedding sand is a flat layer under the pavers, so it is simply area × depth. Joint sand only fills the gaps, so it depends on how much of the surface is joint. For a grid of L × W pavers with joint j, that share is exactly:

joint share = 1 − (L × W) ÷ ((L + j) × (W + j)) joint sand (cu ft) = area × joint share × (paver thickness − 1/8") ÷ 12 × 1.15

The share is the same for running bond, basketweave and herringbone, because every paver still borders one joint on two of its sides. We fill to 1/8" below the top, as polymeric sand makers ask, add 15% for sweeping and settling, and convert at about 100 lb per cubic foot.

Some calculators count each joint twice (once for each paver beside it) and overstate polymeric sand by up to half. A quick check: 12" × 12" slabs have 24" of joint per square foot (one 12" joint on two sides), not 48".

Bedding sand for common areas (1")

AreaCubic feetCubic yardsTons0.5 cu ft bags
100 sq ft9.20.340.4619
200 sq ft18.30.680.9237
300 sq ft27.51.021.3855
400 sq ft36.71.361.8374
500 sq ft45.81.72.2992
1000 sq ft91.73.44.58184

Includes 10% for screeding.

Polymeric sand coverage per 50 lb bag

Paver1/8" joints3/16" joints1/4" joints
4" × 8" brick / Holland (2 3/8" thick)51 sq ft35 sq ft27 sq ft
6" × 6"57 sq ft39 sq ft30 sq ft
6" × 9"69 sq ft46 sq ft35 sq ft
6" × 12"76 sq ft51 sq ft39 sq ft
8" × 8"76 sq ft51 sq ft39 sq ft
12" × 12" slab136 sq ft91 sq ft69 sq ft
12" × 24" slab180 sq ft121 sq ft91 sq ft
16" × 16" slab180 sq ft121 sq ft91 sq ft
24" × 24" slab269 sq ft180 sq ft136 sq ft

Manufacturers print their own coverage ranges, which also depend on how well the base sand was compacted into the joints. Use this table for ordering and keep the receipt for an unopened spare bag.

Frequently asked questions

How do I calculate how much paver sand I need?

Bedding sand: area (sq ft) × depth (in) ÷ 12 = cubic feet; divide by 27 for cubic yards and add about 10% for screeding. At 1" deep, 100 sq ft takes 8.3 cu ft (0.31 cu yd) before the allowance. Joint sand depends on the joints, not the area alone: see the polymeric sand table above.

How many square feet does a 50 lb bag of polymeric sand cover?

It depends on the paver size, the joint width and the paver thickness. With 1/8" joints a bag covers roughly 51 sq ft of 4" × 8" pavers but about 136 sq ft of 12" × 12" slabs, because large slabs have far fewer joints. Wider joints cut coverage quickly.

Is 2 inches of sand too much for pavers?

Yes. The bedding layer should be about 1" after the pavers are compacted (1"–1.5" before). A thicker sand bed shifts and ruts under load. Fix low spots in the gravel base, not with extra sand.

How much is 1 yard of paver sand?

One cubic yard is 27 cu ft and weighs about 1.35 tons (2,700 lb), the same as 54 bags of 0.5 cu ft. Bulk prices vary a lot by region and delivery distance, so compare the yard price plus delivery with the bag price × 54.

What sand goes under pavers?

Coarse, washed concrete sand (ASTM C33). Do not use fine play sand, mason sand or stone dust as the bedding layer: they hold water and do not let the pavers settle evenly. Stone dust is sometimes used in the joints of natural stone instead.

How many bags of polymeric sand for a 200 sq ft patio?

About 4 bags of 50 lb for 4" × 8" pavers with 1/8" joints, or 2 for 12" × 12" slabs. Buy one spare bag: a short bag midway through activation leaves a visible line.

Last reviewed November 22, 2026. How we check our math: About FlooringMath.