Skip to content
FlooringMath
Menu

Paver Installation Cost Calculator

The installed cost of a paver patio, walkway or driveway, built from real quantities (pavers, base, sand, edging, soil to haul away) and a labor rate you can replace with your contractor's.

Units
1. Area
  1. Net area: —

2. Project
3. Prices

Estimated cost

Enter the area.

How the estimate is built

Instead of one price per square foot, the calculator works out the materials the job really needs and prices them, then adds labor:

  • Pavers: area plus pattern waste × price per sq ft.
  • Gravel base: depth from the project and soil (patio 4"–6", driveway 8"–12"), extended 6" past the edges, plus 20% for compaction, converted to tons at 1.4 t/cu yd.
  • Bedding sand: 1" layer plus 10%; polymeric sand from the joint volume of 4" × 8" pavers; edging on edges not against the house.
  • Haul-away: excavation (base + sand + paver thickness) over the base area, × 1.25 because dug soil swells.
  • Labor: per sq ft by project type, or your rate.

Estimates for common sizes

Concrete pavers, running bond, well-drained soil, soil hauled away, default prices.

ProjectLowTypicalHighTypical per sq ft
10 × 10 ft patio$1,511$2,069$3,036$20.69
12 × 16 ft patio$2,831$3,902$5,759$20.32
20 × 20 ft patio$5,802$8,032$11,902$20.08
3 × 30 ft walkway$1,593$2,095$3,056$23.28
12 × 24 ft driveway$5,412$7,306$10,380$25.37
20 × 24 ft driveway$8,872$12,028$17,152$25.06

Assumptions

Labor per sq ftLowTypicalHigh
patio$8.00$12.00$18.00
walkway$9.00$13.00$20.00
driveway$10.00$15.00$22.00
Pavers per sq ftLowTypicalHigh
Concrete pavers$3.00$4.50$8.00
Clay brick pavers$4.00$6.00$10.00
Natural stone (flagstone, travertine, bluestone)$6.00$12.00$25.00
Permeable concrete pavers$5.00$7.00$12.00

Sealing: $1.00–$3.00 per sq ft. Bulk material prices (base $45/ton, sand $50/ton, polymeric sand $30/bag, edging $20 per 8 ft piece, haul-away $35 per cu yd) are editable defaults: delivery fees and regional prices vary widely. These ranges are planning assumptions, not quotes. For the quantities alone, use the paver calculator.

Ask each contractor for base depth, compaction method, edge restraint type and whether haul-away is included. A low bid with a 2" base is not the same job as a 6" base.

Frequently asked questions

How much does a paver patio cost per square foot?

With our default assumptions (concrete pavers, professional installation, soil hauled away) a patio comes to roughly $14.75–$30.00 per sq ft, typically around $20.32. Natural stone or a difficult site (slopes, poor access, steps) costs more.

How much does a 20×20 paver patio cost?

About $5,802–$11,902 installed, typically $8,032, for 400 sq ft of concrete pavers on a 4" base. Labor is the largest line, followed by the pavers.

Why does a paver driveway cost more than a patio?

A driveway needs a base two to three times deeper (8"–12" instead of 4"–6"), thicker 3 1/8" (80 mm) pavers, more excavation and haul-away, and heavier compaction. Labor rates are higher too.

Is it cheaper to install pavers yourself?

You save the labor line, which is usually more than half of the cost, but you pay for a plate compactor and saw rental, delivery fees and many weekends of digging. A small patio or walkway on good soil is a reasonable DIY job; a driveway is not.

What is not included in this estimate?

Retaining walls, steps, drainage, lighting, permits, design, removal of trees or roots, and access problems (no machine access means hand digging). Add those separately.

Last reviewed November 22, 2026. How we check our math: About FlooringMath.