Skip to content
FlooringMath
Menu

Tile Calculator

Tiles and boxes for any floor or wall, with the grout joint, waste for your layout pattern, the cuts you will make at the walls, and the thinset, grout and backer board to go with it.

Units
1. What are you tiling?
  1. Subtract a tub, cabinets, island, door or window

      Net area: —

    Type sizes the way you measure them: 12' 6", 150" and 12.5 all work.

    2. Tile
    3. Layout and waste

    Straight (grid / stacked): Cuts only along the walls, and an offcut from one wall often fits the opposite wall.

    4. Box and price (from the carton)
    5. Thinset, grout and backer board

    You need

    Enter a room size and a tile size to see the result.

    How the tile calculator works

    It follows the same steps a tile setter does on paper, without the rounding shortcuts:

    1. Area. Each room or wall is a rectangle, an L-shape, a triangle, a circle or an area you already know. Cutouts (a tub, cabinets, an island, a door) are subtracted.
    2. Tile coverage with the joint. A tile covers its own size plus half a joint on every side, so the calculator divides by (length + joint) × (width + joint).
    3. Waste. The allowance follows the pattern you choose and goes up by 5% for areas under 50 sq ft. You can type your own.
    4. Round up, twice. Tiles are rounded up, then boxes are rounded up. We never round a box down, and we strip floating-point noise so 220.0000001 sq ft does not cost you an extra box.
    tiles = ⌈ area × (1 + waste%) ÷ ((L + j) × (W + j) ÷ 144) ⌉ boxes = ⌈ tiles ÷ tiles per box ⌉ or ⌈ tiles × (L × W ÷ 144) ÷ sq ft per box ⌉

    L and W are the tile length and width in inches, j the joint in inches, and 144 converts square inches to square feet.

    Worked example: an L-shaped kitchen

    A kitchen measures 14 ft × 12 ft with a 5 ft × 4 ft corner missing, and a 6 ft × 3 ft island that will not be tiled. The tile is 12" × 24" porcelain with 1/8" joints in a 1/3 offset (12% waste), 8 tiles per box.

    • Area: 14 × 12 − 5 × 4 − 6 × 3 = 130 sq ft
    • One tile with its joint: 24 1/8" × 12 1/8" = 2.031 sq ft
    • Exact tiles: 130 ÷ 2.031 = 64; with 12% waste 71.7 → 72 tiles
    • Boxes: 72 ÷ 8 = 9 → 9 boxes (72 tiles)
    • Thinset with a 1/2" square notch and back-buttering: 5 × 50 lb; grout: about 7.8 lb, so one 25 lb bag.

    Waste allowance by layout pattern

    Waste is not a fixed 10%. It comes from cuts: every tile that meets a wall, a cabinet or a doorway is cut, and only some offcuts can be used elsewhere. Patterns with more cuts, or angled cuts, waste more.

    PatternStarting wasteWhy
    Straight (grid / stacked)10%Cuts only along the walls, and an offcut from one wall often fits the opposite wall.
    Brick / running bond (1/2 offset)12%Every row ends in a cut; the leftover piece can usually start the next row, but not always.
    1/3 offset (best for long tiles)12%Same as brick, with three row starts to manage. Recommended for tiles longer than 18" to limit lippage.
    Diagonal (45°)15%Every tile that meets a wall is cut on a 45° angle, and many half-triangles cannot be reused.
    Herringbone, square to walls15%The zig-zag edge must be cut along every wall; offcuts are odd shapes.
    Herringbone, 45° to walls20%Angled cuts on every edge piece plus a zig-zag pattern: the most offcuts that cannot be reused.
    Chevron15%Chevron tiles are pre-cut parallelograms; both ends of every row need angled cuts.
    Versailles / French pattern15%Mixed tile sizes repeat in a module; edges break modules, and the sizes come in fixed ratios per box.

    Add about 5% for small rooms (under 50 sq ft), rooms with many corners or pipes, and large-format tile where one broken tile is a big share of the job. Keep a few spare tiles from the same lot: matching a discontinued tile years later is often impossible.

    Tiles per square foot for common sizes

    Calculated with a 1/8" joint. "To buy" adds 10% waste and rounds up.

    Tile sizeFace areaTiles per sq ft100 sq ft, exact100 sq ft, to buy
    12" × 12"1 sq ft0.97997.9108
    12" × 24"2 sq ft0.49249.255
    24" × 24"4 sq ft0.24724.728
    18" × 18"2.25 sq ft0.43843.849
    16" × 16"1.778 sq ft0.55455.461
    13" × 13"1.174 sq ft0.83683.692
    24" × 48"8 sq ft0.12412.414
    6" × 24" (wood look)1 sq ft0.97597.5108
    6" × 36" (wood look)1.5 sq ft0.65165.172
    8" × 48" (wood look)2.667 sq ft0.36836.841
    3" × 6" subway0.125 sq ft7.523752.3828
    4" × 12" subway0.333 sq ft2.879287.9317
    2" × 8"0.111 sq ft8.34834918
    4" × 4"0.111 sq ft8.463846.3931
    4 1/4" × 4 1/4"0.125 sq ft7.523752.3828
    6" × 6"0.25 sq ft3.838383.8423
    8" × 8"0.444 sq ft2.181218.1240

    More sizes, with real (actual) dimensions and box coverage, are in the tile sizes chart.

    Where to start the first row

    For a straight or offset layout on a rectangular area, the result panel shows how many tiles fit along each wall and the size of the cut pieces for three ways to start: against a wall, with a tile centered on the room, or with a grout joint centered on the room. It picks the start that avoids thin slivers, which are hard to cut and look like a mistake. A cut under about a third of a tile at a doorway or along the most visible wall is the one to avoid.

    Thinset, grout and backer board

    • Thinset: coverage per 50 lb bag depends on the trowel notch, which depends on the tile size: about 90 sq ft with a 1/4" × 1/4" square notch, 65 sq ft with 1/4" × 3/8" and about 42 sq ft with 1/2" × 1/2". Tiles longer than 15" should be back-buttered; we add 20% for that. Details in the thinset calculator.
    • Grout: computed from the real joint volume (area × joint share × tile thickness), not from a flat coverage figure, so small tiles with wide joints correctly need far more grout. See the grout calculator.
    • Cement backer board: 3 ft × 5 ft (15 sq ft) sheets are the easiest to carry and cut; we add 10% for cuts and estimate screws on an 8" grid. On floors the board is set in a bed of thinset, so the calculator adds bags for that.

    These are estimates for ordering. Real coverage of thinset and grout varies with the substrate, the trowel angle and the tile back. Check the coverage chart on your product and buy from one production lot (the shade and caliber codes on the carton should match).

    Frequently asked questions

    How do I calculate how many tiles I need?

    Measure the area in square feet (length × width, minus anything you will not tile), divide by the area of one tile including its grout joint, add a waste allowance for cuts and breakage (10% for a straight layout, 15% for diagonal, up to 20% for herringbone), and round up. Then divide by the tiles (or square feet) per box and round up again: tile is only sold in whole boxes.

    How many tiles do I need for a 10×10 room?

    A 10 ft × 10 ft room is 100 sq ft. With 1/8" joints and 10% waste you need about 108 tiles of 12" × 12", 55 tiles of 12" × 24", 28 tiles of 24" × 24", 108 tiles of 6" × 24". Diagonal or herringbone layouts need 5–10% more.

    How many boxes of tile do I need?

    Take the tiles you need including waste and divide by the pieces per box, or multiply them by the area of one tile and divide by the square feet printed on the box. Always round up. Our calculator shows both the box count and the leftover tiles you will have, so you can see whether one more box is worth it.

    Does the grout joint change how many tiles I need?

    Yes, a little for large tile and a lot for small tile. A 1/8" joint on 12" × 12" tile means each tile covers 12 1/8" × 12 1/8", about 2% fewer tiles. A 1/4" joint on 4" × 4" tile cuts the count by about 12%. Most simple calculators ignore the joint; we include it.

    How much extra tile should I buy?

    Plan 10% for a straight layout in a normal room, 12% for brick or 1/3 offset, 15% for diagonal or herringbone square to the walls, and 20% for herringbone at 45°. Add about 5% more for small rooms like a bathroom floor, and keep a few spare tiles for future repairs. See how much extra tile to buy.

    How do I calculate tile for a wall?

    Multiply the wall length by the height you will tile, then subtract doors and windows (a standard interior door is about 3 ft × 6 ft 8 in, about 20 sq ft). Enter each wall as its own area with "Height" in place of width, or use the shower tile calculator for tub surrounds and showers.

    Should I tile under cabinets, a vanity or a toilet?

    Under a toilet: yes, tile the whole bathroom floor. Under kitchen base cabinets: usually no; subtract the cabinet footprint, but keep the tile under a dishwasher or range opening so the appliance can slide out. Under a freestanding vanity: yes; under a built-in vanity it is optional.

    How many square feet does a box of tile cover?

    It depends on the tile: boxes of 12" × 24" porcelain often hold 8 tiles (about 15.5–16 sq ft), 24" × 24" boxes hold 4 tiles (about 15.5 sq ft), and 3" × 6" subway tile often comes in boxes of 40–80 pieces (5–10 sq ft). Always use the coverage printed on your carton, because real tile is slightly smaller than its nominal size.

    Last reviewed November 22, 2026. How we check our math: About FlooringMath.