Tile for a walk-in shower or a tub surround: walls to any height, niches, windows, the curb and the shower floor, plus the waterproofing area, cement board, grout, thinset and edge trim.
The back of a niche replaces the wall tile you cut out, so only its four sides are extra. The curb and the niche are usually tiled with the wall tile, the floor with a mosaic. Wall waste starts at 15–17% because of the corners, the valve and the niche; floor waste at 15% because of the cuts around the drain.
Example: 60" × 36" alcove shower
Back 60" + two sides of 36" = 132" of wall × 96" high = 88 sq ft. A 12" × 24" × 3 1/2" niche adds 1.75 sq ft of sides and the curb 5.42 sq ft, so 95.2 sq ft of wall tile: about 322 tiles of 4" × 12" with 15% waste. The floor is 60 × 36 ÷ 144 = 15 sq ft: 18 mosaic sheets. Waterproof 110 sq ft.
Tile area of common shower sizes
Shower
Walls
Floor
36" × 36" corner, 96" high
48 sq ft
9 sq ft
48" × 36" alcove, 96" high
80 sq ft
12 sq ft
60" × 32" alcove, 96" high
82.7 sq ft
13.3 sq ft
60" × 36" alcove, 96" high
88 sq ft
15 sq ft
60" × 30" tub surround, 72" above tub
60 sq ft
—
60" × 30" tub surround, to 96" ceiling (≈ 80" above tub)
66.7 sq ft
—
Before waste, without niches or windows.
Shower details that change quantities
Edge trim: every exposed tile edge (the front edge of the side walls, the top course if you stop short of the ceiling, the niche opening) needs bullnose tile or a metal profile. Profiles come in about 8 ft lengths.
Waterproofing: a sheet or liquid membrane goes over the walls, the floor and the curb, lapped onto the floor. Liquid membranes are sold by coverage per gallon at the required thickness; check the label.
Grout: wall tile in showers often uses 1/16" joints; mosaic floors have many more grout lines, so the floor can need as much grout as all the walls.
Cement board: hung on the studs, 3 × 5 ft sheets, with seams taped. The floor gets a mortar bed or a pre-sloped pan instead.
Add up the walls: back wall × height plus each side wall × height, subtract any window, add the sides of niches, then add 15% waste. A 60" × 36" alcove tiled 96" high has 88 sq ft of walls (about 95 sq ft with a niche and a curb), which is about 322 tiles of 4" × 12". The shower floor is another 15 sq ft, usually in mosaic.
How many square feet of tile for a tub surround?
+
A standard 60" × 30" tub tiled 72" above the rim on three walls is 60 sq ft, about 536 subway tiles of 3" × 6" with 15% waste. Tiling all the way to an 8 ft ceiling adds roughly another 10 sq ft.
How much extra tile should I buy for a shower?
+
Plan 15% to 20% for shower walls: the niche, the valve and shower head, the inside corners and the top course all need cuts. Use 15% for the shower floor too, because the floor slopes to a drain and mosaic sheets are cut around it. Buy one more box if the tile could be discontinued.
Should shower tile go to the ceiling?
+
It is not required: most codes only ask for a water-resistant surface to 72" above the drain. Tiling to the ceiling looks finished, keeps steam off painted drywall and avoids a top trim line; it adds about 15–20% more wall tile.
What size tile is best for a shower floor?
+
Small tiles (2" × 2" or smaller mosaics on sheets) follow the slope to a center drain and give grip because of the many grout lines. Large tiles need a linear drain with a single slope. The calculator handles both.
What else do I need besides tile?
+
Cement board or foam board on the walls, a waterproofing membrane over walls, floor and curb (or a waterproof board system), thinset, grout (often epoxy or urethane in showers), edge trim for exposed edges and silicone for the inside corners and the change of plane at the tub.
Last reviewed November 22, 2026. How we check our math: About FlooringMath.